Driver: EIDE
Last Update: February 18, 1998
Availability Information
A version of this driver is on the OPENSTEP CD-ROM
An updated BETA version of this driver, version 4.03, is avaiable on Apple's FTP servers at:
ftp://ftp.info.apple.com/Apple_Support_Area/Apple_Software_Updates/MultiCountry/Enterprise/openstep/drivers/beta/EIDE.pkg.compressed
Driver Name / Installer .pkg: EIDE
Driver Type: System
Driver Scope: Generic-System
Supported Components: PC Tech RZ1000
PC Bus / Interface Supported by Driver*: Integrated, ISA, PCI
Supported Connectors: 40-pin Header (Internal IDE)
Access Mode: PIO
Adapter Memory:
General Overview notes: This drivers supports IDE disks and IDE ATAPI rev. 1.2 compliant CD-ROMs. It supports primary and secondary IDE controllers with up to 2 drives per controller.
This driver replaces the IDE driver distributed on the NEXTSTEP 3.3 CD.
Supported Products / Add-on Adapters:
The following ATAPI CD-ROM drives are supported:
Chinon CD-ROM CDS-525 (2X), firmware rev. W09
Matsushita CD-ROM CR-571 (2X), firmware rev. 1.0e -- Panasonic
Mitsumi CD-ROM 1B (4X), firmware rev. B02 -- model FX400
Sony CD-ROM CDU55E (2X), firmware rev. 1.0u
Sony CD-ROM CDU76E-S (4X), firmware rev. 1.0c
Toshiba CD-ROM XM-5302TA (4X), firmware rev. 0305
Philips CM207, firmware rev 1.10 (??) -- reported to work
SONY CD-ROM CDU76E-Q, firmware rev 1.0c (4X)
SONY CD-ROM CDU55D, firmware rev 1.0v (2X)
SONY CD-ROM CDU77E, firmware rev 1.0e (4X)
TORiSAN CD-ROM CDR-S1, firmware rev 1.70 (4X) -- SANYO
Chinon CD-ROM CDS-545, firmware rev ERc A1.0 (4X)
GoldStar CD-ROM GCD-R540, firmware rev 1.17 (4X)
GoldStar CD-ROM GCD-540C, firmware rev 1.01 (4X)
SANYO CRD-254P, firmware rev 1.02 (4X)
MATSHITA CD-ROM CR-574, firmware rev 1.06 (4X) -- Panasonic
Pioneer CD-ROM DR-UA124X, firmware rev 1.02 (4X) -- force detection
MITSUMI CD-ROM !B, firmware rev K02 (4X) -- DRM FX400B
TEAC CD-55E, firmware rev ?? (4X) -- Thinkpad 760CD
ATAPI CD-ROM SPEED-6X, firmware rev 6.2D (6X) -- ACER 665A
VERTOS 600ESD CD-ROM X6-IDE, firmware rev 1.20 (6X)
TEAC CD-56E, firmware rev 1.0D (6X)
MATSHITA UJDCD4700, firmware rev 1.11 (??)
TEAC CD-58E, firmware rev 1.1B (8X)
Toshiba CD-ROM XM-5602B, firmware rev 1426 (8X)
Sony CD-ROM CDU311, firmware rev 3.0i (8X)
EPSON CMD-2240 SPEED-6X, firmware rev R100 -- reported to work
Hitachi CDR-7730, firmware 1.1a (4X)
TEAC CD-524E, firmware 4.0D (24X)
Supported Products / Systems (ie integrated into PC System):
Other ATAPI 1.2 compliant CD-ROM drives should work with NEXTSTEP even if they are not in the supported list.
Special Features of Driver / Driver Notes:
NeXT's EIDE driver is not affected by the RZ1000 hardware bug.
This device driver provides information in the Configure application's help panel. Choose Info>Help from the Configure menu and scroll down to find this device driver's help topic.
Known Problems
These devices are not supported.
1. NEC CDR-260 (2X)
2. NEC CDR-273
To get the Pioneer DR-UA124X 1.02 CD-ROM to work you must force detection. You can do this by going in Expert mode and adding the key "Slave"="ATAPI" (or "Master" as the case may be) to the table.
Driver Version Notes
3.33 - This version adds support for several new ATAPI CD-ROM drives and fixes some bugs.
3.34 - Fixed a bug which could cause machines to hang under very heavy load. Released on OPENSTEP 4.0 User CD-ROM
4.02 - Added device overrides and modified the inspector. The new overrides are documented in the driver help.
4.03 - Improved ATAPI support. Added support for Intel PIIX PCI IDE controllers. Added Bus Master support. Revised the driver Inspector.
New Driver / Update Description:
Use the following installation instructions when installing from a CD-ROM drive connected to the secondary EIDE controller:
1. Select Primary/Secondary(Dual) EIDE and ATAPI
Device Controllers as the hard disk driver.
2. After the install program has finished reading
from the CD-ROM, the Configure panel will
appear. Double-click the Other icon. If the
Primary/Secondary(Dual) EIDE and ATAPI
Device Controllers driver is listed, remove it from
the list. It is no longer necessary since the
installation from the CD-ROM is complete. Add the
appropriate EIDE driver to match your EIDE
hardware configuration. You will need to add it
twice to get a second instance of the EIDE
driver to support the secondary EIDE
controller. You will need to set the IRQ to 15, and
I/O port address range to 0x170-0x177 in the
second instance of the driver, in order to avoid
conflicts with the first instance. Add any other
necessary drivers while in Configure, and then
click on theSave button.
* - Indicates information that is inclusive of the entire capability of this driver. Not all devices supported by this driver may include all features listed. Check any available NeXTanswers and the hardware manual for the device for additional information.